Skip to main content

🇻🇳 178 profiles · Engineering review

Vietnam Manufacturing

How Should the IQC Process for Stamping Parts Be Done?

July 23, 2026

Stamping press on the production floor at Tan Phong An Industrial Company Limited (2), a DEWIN-audited Vietnamese factory

Overview of the IQC process workflow for inspecting stamping parts

A weak [IQC process for stamping parts](https://dewintech.com/blog/how-perform-incoming-quality-control-iqc-stamping-parts/) lets bad brackets slip into your warehouse ANSI/ASQ Z1.4 1. I have seen one missed burr check turn into a costly recall for a client’s assembly line.

The IQC process for stamping parts should verify supplier documentation against the drawing, perform visual and dimensional checks on an AQL-based sample, test material properties like hardness, and then accept, reject, or hold each lot with full traceability records before release to production.

That is the short answer. Below, I break each step into a practical workflow you can apply to your next incoming shipment of stamped parts.

What Should I Include in an IQC Checklist for Stamping Parts?

Last year, our Vietnam team caught a batch of Z-clips with hairline cracks at the bend radius ISO 2859-1 2. The supplier's own report had missed it. A good checklist made the difference.

An IQC checklist for stamping parts should cover documentation review, material certification, visual surface inspection, dimensional verification against the drawing, hardness testing, plating or coating checks, burr and edge condition, spring-back at bends, and functional fit with mating components.

IQC checklist covering documentation, dimensions, hardness, and surface checks for stamping parts

A checklist works only when it matches the failure modes of stamping. Stamped brackets and clips fail in predictable ways. Burrs cut assembly workers. Cracks form at tight bend radii. Spring-back shifts flange angles out of tolerance. Wrong material grade ruins strength or corrosion resistance. So your checklist must target these risks directly, not just copy a generic template.

Core Checklist Items

Here is the structure we use across our stamping projects for U.S. clients:

Category What to Check Typical Tools
Documentation PO, drawing revision, MTR/CoC, PPAP status 3 Document comparison
Material Grade, thickness, hardness, coating spec Micrometer, hardness tester
Visual Burrs, scratches, rust, dents, cracks, oil residue Eyes, magnifier, light box
Dimensional Hole positions, bend angles, flange heights, flatness Calipers, height gauge, CMM
Functional Fit with mating part, fastener engagement Go/no-go gauges, fixtures
Packaging Damage, mixing of lots, labeling, rust protection Visual check

Stamping-Specific Items Most Checklists Miss

Generic IQC checklists often skip three things. First, check spring-back on bent flanges. A 90-degree bend that reads 92 degrees will not sit flush on the mounting surface. Second, inspect the bend radius under magnification for micro-cracking, especially on harder materials or zinc-plated steel. Third, verify grain direction where the drawing calls it out. Bends made against the grain crack more easily in service.

We also log the die lot or production run when the supplier provides it. That single data point speeds up root-cause work later if a defect trend appears.

✔ A stamping IQC checklist should include spring-back and bend-radius crack checks, not just holes and outlines True
Spring-back and micro-cracking at bends are among the most common stamping-specific failure modes, and they often pass a basic dimensional check while still causing assembly or field failures.
✘ If the supplier provides a material certificate, you do not need to verify the material yourself False
Certificates can be attached to the wrong lot or contain transcription errors, so a quick hardness or thickness check on the actual parts remains essential to confirm the paperwork matches reality.
Video: Sample metal parts from audited Vietnamese factories in the DEWIN network. (@dewintech)

How Can I Verify Supplier Compliance with My Drawing Requirements During IQC?

A purchasing manager once told me his biggest fear was suppliers "silently improving" a part. Our team in China now compares every incoming lot against the frozen drawing revision, line by line.

Verify drawing compliance by confirming the drawing revision on the PO matches the supplier's, checking every critical-to-quality dimension marked on the drawing, comparing material certificates to the specified grade, and validating tolerances, coatings, and notes with a ballooned drawing and dimensional report.

Verifying supplier drawing compliance using ballooned drawings and dimensional reports during IQC

Drawing compliance is where most non-conformances hide. The part can look fine but still violate a note buried in the title block. So we treat the drawing as a contract and audit it in a fixed sequence.

Step-by-Step Verification Method

  1. Confirm the revision. Check that the supplier built to the same drawing revision listed on your PO. A surprising number of disputes trace back to an outdated print on the shop floor.
  2. Balloon the drawing. Number every dimension, tolerance, and note. This creates a checklist that nothing can slip past.
  3. Classify characteristics. Mark each ballooned item as critical, major, or minor. Critical items get measured on every sampled part. Minor items get spot checks.
  4. Cross-check the MTR. Compare the mill test report 4 chemistry and mechanical properties against the material callout, including standards like ASTM or EN grades.
  5. Verify coatings and finishes. Confirm plating type and thickness where specified. A zinc coating that is too thin fails salt-spray 5 expectations later.
  6. Check the notes. Deburr requirements, grain direction, burr-side orientation, and marking requirements all live in drawing notes. Audit each one.

Handling Ambiguity

Sometimes a drawing is silent on something that matters, such as burr height or edge condition. In our co-development projects, we resolve these gaps in writing before the first production PO. During IQC, we then inspect against that agreed standard, not against assumptions. If your supplier ever says a requirement was "unclear," that is a signal to tighten the drawing, not loosen the inspection.

We also ask suppliers to submit a dimensional report with each lot. IQC then becomes a verification of their data, which is faster and builds shared accountability.

✔ A ballooned drawing with classified characteristics is the most reliable way to audit drawing compliance at IQC True
Ballooning turns the drawing into an exhaustive checklist, and classifying items by criticality focuses inspection effort where a deviation would cause real functional harm.
✘ If a part fits the mating component, it must comply with the drawing False
Fit checks miss material grade, coating thickness, hardness, and note requirements, all of which can cause corrosion, fatigue, or strength failures even when the part assembles perfectly.

What Sampling Plan Should I Use for Incoming Inspection of Stamped Parts?

There is a real trade-off here that I weigh on every project: inspect too much and you burn budget, inspect too little and defects reach your customer. Sampling plans exist to balance that tension.

Use AQL sampling per ANSI/ASQ Z1.4 or ISO 2859-1 with General Inspection Level II, setting AQL 0.65–1.0 for critical characteristics, 1.5 for major defects, and 2.5–4.0 for minor defects, then tighten or reduce sampling based on supplier performance history.

AQL sampling plan per ANSI/ASQ Z1.4 for incoming inspection of stamped parts

One hundred percent inspection of stamped parts is rarely practical, and it is often less accurate than a disciplined sample. Inspector fatigue is real. A well-run AQL plan gives you statistical confidence without checking every clip in a box of ten thousand.

Typical AQL Setup for Stamped Parts

Defect Class Example for Stamped Brackets Suggested AQL
Critical Cracks at bend radius, wrong material, missing hole 0.65
Major Out-of-tolerance hole position, excessive burr, bent flange angle 1.0–1.5
Minor Light scratches, minor cosmetic marks, faint oil residue 2.5–4.0

For a lot of 3,201 to 10,000 parts at Level II, you would inspect 200 pieces. The tables in Z1.4 then give you the accept and reject numbers for each AQL. If defects exceed the reject number, the whole lot goes on hold.

Risk-Based Adjustments

Static sampling wastes resources. We adjust inspection depth based on three factors. First, supplier history: a vendor with clean lots over a sustained period can move to reduced inspection or skip-lot sampling. Second, part criticality: a safety-related automotive bracket never gets reduced sampling, while a simple furniture clip might. Third, change events: any new die, material lot change, or process change resets the supplier to normal or tightened inspection until results stabilize.

In our supply chain work between Vietnam and the U.S., this tiered approach has kept inspection costs sensible while protecting our clients from the lots that actually carry risk. The key is writing the switching rules down so the decision is systematic, not a judgment call made under delivery pressure.

How Do I Handle Non-Conforming Stamping Parts Found During IQC?

Early in one project, a rejected lot sat unlabeled next to accepted stock, and a warehouse worker nearly shipped it. That near-miss taught our team to make segregation the very first action, before any paperwork.

Handle non-conforming stamped parts by immediately segregating and labeling the lot, documenting the defect with photos and measurements, issuing a formal non-conformance report to the supplier, deciding disposition through use-as-is, sort, rework, or return, and requiring corrective action before the next shipment.

Handling non-conforming stamped parts with segregation, documentation, and corrective action

A rejection without a disposition process just creates a pile of metal and an argument. The goal is a controlled, documented flow that protects production, holds the supplier accountable, and prevents repeats.

The Disposition Workflow

  1. Quarantine first. Move the lot to a marked hold area. Tag it with the NCR number, date, and defect description. Physical separation prevents accidental release.
  2. Document the evidence. Take photos, record measurements, and note the sample size and defect count. Reference the ballooned drawing item that failed.
  3. Notify the supplier fast. Send the non-conformance report within one or two working days. Delays weaken your claim and slow the fix.
  4. Decide the disposition. Involve quality and engineering, not just purchasing.
  5. Close the loop. Require root-cause analysis 6 and corrective action, then verify the fix on the next incoming lot with tightened inspection.

Choosing the Right Disposition

Disposition When It Fits Watch Out For
Use as is Deviation has no functional or cosmetic impact; customer approves Requires documented concession, never a verbal OK
Sort (100% screen) Defect rate is low and detectable; production needs parts now Agree who pays for sorting labor before starting
Rework Defect is correctable, e.g., deburring or re-flattening Rework must not create new defects like tool marks
Return / replace High defect rate, material errors, or safety-critical failures Confirm replacement lead time against your line schedule

Cost recovery matters too. Sorting, rework, and freight for returns should be charged back per your supplier agreement. Just as important, feed every NCR into your supplier scorecard. Two or three repeat non-conformances on the same characteristic signal a process problem, and that calls for a supplier audit 7 rather than another round of sorting. In our experience managing suppliers across Vietnam and China, the audit conversation fixes what a hundred NCRs cannot.

✔ Non-conforming lots must be physically segregated and labeled before any disposition decision is made True
Unsegregated rejected stock is the most common cause of bad parts accidentally entering production or shipping, so quarantine is the first and most urgent control step.
✘ Returning every non-conforming lot to the supplier is always the safest choice False
Blanket returns can starve your production line; controlled options like sorting,

Frequently Asked Questions

What Should I Include in an IQC Checklist for Stamping Parts?

Last year, our Vietnam team caught a batch of Z-clips with hairline cracks at the bend radius ISO 2859-1 2 . The supplier's own report had missed it. A good checklist made the difference.

How Can I Verify Supplier Compliance with My Drawing Requirements During IQC?

A purchasing manager once told me his biggest fear was suppliers "silently improving" a part. Our team in China now compares every incoming lot against the frozen drawing revision, line by line.

What Sampling Plan Should I Use for Incoming Inspection of Stamped Parts?

There is a real trade-off here that I weigh on every project: inspect too much and you burn budget, inspect too little and defects reach your customer. Sampling plans exist to balance that tension.

Manufacturing RFQ

Have a STEP Model or 2D Drawing for This Project?

Share your drawing, material, quantity and finishing requirements to begin a manufacturing quote. Confirm pricing, delivery and inspection requirements during the review.

Upload CAD & Get Quote →

This article is part of DEWIN's technical manufacturing engineering knowledge base. Factory-specific details come from each factory's profile page — please verify current information there or with our team.

Quick Sourcing Inquiry