A missing material test report 1 once cost one of our clients a six-week production delay and thousands in scrapped stamping parts 2 — a problem we now prevent at the sourcing stage.
To request material test reports and certificates when sourcing stamping parts, specify the required MTR type (e.g., EN 10204 3.1) in your RFQ, demand heat number traceability, verify chemical composition and mechanical properties against your engineering specs, and require delivery of original documents before shipment approval.
This guide walks through exactly what to ask for, how to verify what you receive, and how to build material traceability 3 into your sourcing process from day one third-party inspection agency 4. Whether you source stamping parts from Vietnam or elsewhere in Asia, the steps below will protect your supply chain.
What specific material certifications should I demand to ensure my stamping parts meet my engineering specs?
One trade-off I weigh on every new stamping project is how deeply to specify material certification requirements — too vague and you get generic paperwork, too prescriptive and you scare off capable suppliers who simply use different document formats.
Demand a Mill Test Certificate (MTC) or Material Test Report (MTR) that includes the material grade, heat number, chemical composition, mechanical properties (tensile strength, yield strength, elongation), and an inspector's signature — all referencing the specific industry standard (ASTM, ASME, or EN) called out in your drawing.
/12-05-2025-Pictures%20-%20Name/Hydraulic%20press%201.jpg)
Understanding the Documents: MTR, MTC, and CoA
The terms Material Test Report (MTR) and Mill Test Certificate 5 (MTC) are used interchangeably across the metals industry. Both describe the same document — a "report card" for the metal that details its origin, manufacturing process, and test results. A Certificate of Analysis 6 (CoA) serves a similar function but is more common in chemicals and pharmaceuticals, not metals. For stamping parts, you want an MTR or MTC.
When our Vietnam office reviews incoming material for a stamping project, the first thing we check is whether the document references the correct standard. If your drawing calls out ASTM A1008 for cold-rolled steel, the MTR must certify compliance against that exact specification. A generic certificate that says "carbon steel" is not enough.
Which Certifications to Specify in Your RFQ
The level of certification you need depends on your end-use application. Here is a quick reference:
| Certification Level | What It Covers | When to Require It |
|---|---|---|
| EN 10204 2.1 | Manufacturer's declaration of compliance (no test data) | Low-risk, non-critical parts |
| EN 10204 2.2 | Declaration with routine test results from the batch | Standard commercial parts |
| EN 10204 3.1 7 | Specific test results from an authorized inspector at the mill | Automotive, structural, or safety-critical stamping parts |
| EN 10204 3.2 | Test results verified by both the manufacturer and an independent body | Aerospace, pressure vessels, or regulated applications |
For most custom stamping parts we handle for U.S. buyers, EN 10204 3.1 is the minimum standard I recommend. It provides actual test data — not just a promise — tied to the specific heat of metal used in your parts.
Key Data Points Every MTR Must Include
Not all MTRs are created equal. Some suppliers hand over a single page with a material name and a stamp. That is not acceptable for mid-to-high quality stamping parts. Here is what a valid MTR must contain:
- Heat Number: The unique identifier tying the material back to its production batch at the mill.
- Material Grade and Specification: For example, ASTM A1008 CS Type B, or SUS304 per JIS G4305.
- Chemical Composition: Percentages of carbon, manganese, phosphorus, sulfur, silicon, and any alloying elements.
- Mechanical Properties: Tensile strength, yield strength, elongation percentage, and hardness (if specified).
- Dimensions: Thickness and coil/sheet width.
- Inspector Signature and Quality Control Stamp: Without these, the document has no authority.
I always tell our clients: if any of these fields are blank or generic, push back before you approve the material. Once stamping starts on the wrong material, there is no fixing it.
Why Formability Depends on Certified Properties
Stamping is a forming process. The metal must bend, stretch, and flow into a die without cracking. If the yield strength is too high, the material resists forming and you get cracks. If it is too low, you get excessive springback and dimensional issues. The MTR gives you the actual numbers for the specific coil or sheet being used — not just the nominal values from a data sheet. That difference matters. I have seen parts crack at the flanges because the actual tensile strength was 15% higher than the nominal spec, and nobody checked the MTR before production.
How can I verify that the Material Test Reports provided by my Vietnam supplier are actually authentic?
A lesson we learned early in our Vietnam operations is that not every document stamped with a factory seal tells the full truth — and the buyer who trusts without verifying is the one who pays the price.
Verify MTR authenticity by cross-checking the heat number on the document against the physical marking on the raw material, hiring a third-party inspection agency to conduct on-site sampling and independent lab testing, and watching for red flags such as missing inspector signatures, identical test values across different heats, or chemical data that falls outside the specified grade range.

The Reality of Fraud Risk in Material Documentation
Let me be direct: document fraud exists. It is not unique to Vietnam or any single country. It happens when a supplier uses leftover MTRs from a previous batch, edits values on a scanned document, or simply attaches a mill cert from a different heat of material. Our quality team in Vietnam has caught these issues more than once.
The risk is highest when you source stamping parts from a fabricator who buys raw material from a third-party distributor. The fabricator may not have a direct relationship with the original mill. They may receive material without proper documentation and then produce a "convenient" certificate to satisfy your requirement. This is why supplier qualification includes document verification — not just factory capability.
A Practical Verification Process
Here is a step-by-step approach I use on our projects:
| Step | Action | Purpose |
|---|---|---|
| 1 | Request the original MTR before production starts | Confirms material is on-site and documented |
| 2 | Compare the heat number on the MTR to the physical stamp or tag on the coil/sheet | Ensures the document matches the actual material |
| 3 | Review chemical composition values against the ASTM or JIS grade requirements | Catches documents where values are outside the allowable range |
| 4 | Check for inspector signature, date, and mill identification | Validates the document's authority |
| 5 | Hire a third-party inspection company to take a sample from the actual material | Independent verification of chemical and mechanical properties 9 |
| 6 | Send the sample to an accredited third-party lab for testing | Produces an independent test report to compare against the MTR |
Red Flags to Watch For
Through our experience managing supplier audits and quality assurance across Asia, I have developed a mental checklist of warning signs:
- Identical mechanical property values across multiple heats: Real test data varies slightly between heats. If every MTR from a supplier shows the exact same tensile strength, something is wrong.
- Missing or illegible inspector signature: A valid MTR must be signed. A stamp alone is not enough.
- Heat number format inconsistencies: Each mill has a consistent format for their heat numbers. If the format changes between orders from the same supposed mill, investigate.
- Chemical values at the extreme edge of the specification: While technically compliant, this pattern can indicate the values were chosen to "fit" rather than measured.
- No mill logo or letterhead: Legitimate mills issue certificates on their official letterhead.
When to Invest in Third-Party Lab Testing
Third-party lab testing adds cost — typically $150 to $500 per sample depending on the tests required. But for safety-critical or high-volume stamping parts, it is a risk mitigation investment, not an expense. Consider this: a single batch of non-conforming stamping parts that reaches your customer's assembly line can trigger a recall costing tens of thousands of dollars, plus damage to your reputation. The lab test is cheap insurance.
On our projects, we recommend third-party testing whenever the annual purchase value exceeds $20,000, or when the parts are used in automotive, medical, or structural applications where failure has serious consequences.
Should I require a full MTR and heat lot traceability before I approve the final shipment of my custom parts?
A buyer interaction last year drove this point home for me. A U.S. client approved a shipment of stamped mounting brackets without reviewing the MTR. Two weeks after the parts arrived, his customer's incoming inspection flagged the hardness as out-of-spec. We traced the issue to a material substitution the Vietnamese stamping shop made without informing anyone. Full heat lot traceability would have caught this before the container left the port.
Yes — you should require a full MTR with heat lot traceability before approving any final shipment of custom stamping parts. This creates an unbroken chain from the raw material's origin at the mill, through the fabrication process, to the finished part, enabling you to trace any defect back to its source and protect yourself from liability.

What Heat Lot Traceability Actually Means
Material traceability in stamping is the ability to link every finished part back to the specific heat (batch) of raw material it came from. This requires three things:
- The original mill certificate with a heat number.
- Internal records at the stamping factory showing which heat number was used for which production run.
- Marking or labeling on the finished parts or packaging that references the heat number.
Without all three, the chain is broken. And a broken chain means that if a part fails in the field, you cannot determine whether the problem was the material, the process, or the design. You are left guessing — and your customer is left exposed.
The "Pre-Shipment Gatekeeper" Rule
I enforce a simple operational rule on every project we manage: No MTR, no shipment. This means the MTR and supporting traceability documents must be reviewed and approved by our quality team before the goods are released for packing and shipping. This is not just good practice — it is the final gate in a quality assurance system.
Here is how this fits into a typical control plan for custom stamping parts:
| Quality Gate | Timing | Documents Required | Who Approves |
|---|---|---|---|
| Material Incoming Inspection | Before stamping starts | Original MTR from mill, heat number verification | Supplier QC + DEWIN inspector |
| First Article Inspection (FAI) | First pieces off the die | Dimensional report, material hardness check, MTR reference | Buyer engineering + DEWIN |
| In-Process Inspection | During production run | SPC data, visual checks, process parameter log | Supplier QC |
| Final Inspection | After production, before packing | Full dimensional report, MTR, heat lot traceability record, visual inspection | DEWIN final inspector |
| Pre-Shipment Approval | Before container loading | All documents compiled and reviewed | Buyer + DEWIN |
What Happens When Traceability Is Missing
Let me paint a realistic scenario. A stamping factory uses two different coils of SUS304 stainless steel on the same production run because the first coil ran out mid-batch. One coil has a slightly higher carbon content than the other. The parts look identical. But when your customer welds or heat-treats them, the higher-carbon parts develop intergranular corrosion. Without heat lot traceability, you cannot tell which parts came from which coil. Your only option is to scrap or re-inspect the entire shipment. That is expensive, time-consuming, and completely avoidable.
Small Orders Are Not an Exception
Some suppliers argue that traceability is too burdensome for small orders. I respectfully disagree. Material integrity does not scale with volume. A single stamped bracket in a safety-critical assembly can cause just as much damage as a thousand. The documentation effort is modest — it is a matter of recording the heat number and keeping the mill cert on file. Any supplier who refuses this basic step is not a supplier I would recommend for custom parts with mid-to-high quality requirements.
How do I communicate my material testing requirements to ensure my stamping project passes a strict PPAP audit?
When we first started managing Production Part Approval Process 10 submissions for U.S. automotive clients, I realized that most PPAP rejections related to stamping parts were not caused by dimensional errors — they were caused by incomplete or missing material documentation. The PPAP auditor expects a complete material story, and if you have not told your supplier exactly what that story needs to include, you are setting yourself up for failure.
Communicate material testing requirements by embedding them directly into your RFQ, purchase order, and control plan — specifying the MTR type (e.g., EN 10204 3.1), the required PPAP submission level (e.g., Level 3), the exact material grade and specification, the mechanical and chemical test parameters, and the heat number traceability format — so your supplier cannot claim ambiguity during the audit.

Build Material Requirements into Every Document
The most common mistake buyers make is assuming the supplier knows what material documentation is needed. They do not — or at least, their definition of "sufficient" may differ from yours. I recommend specifying your material testing requirements in at least three places:
-
The RFQ: State the MTR requirement, the certification level, and the standard. For example: "Supplier shall provide MTR per EN 10204 3.1 for all raw materials used. MTR must include heat number, chemical composition, and mechanical properties certified against ASTM A1008."
-
The Purchase Order: Reiterate the MTR requirement and add a clause: "Shipment will not be approved without submission and approval of the MTR."
-
The Control Plan: Include a line item for material verification at incoming inspection, referencing the MTR and the specific tests to be performed.
This triple-layer approach removes any ambiguity. When the PPAP auditor asks your supplier, "How do you verify incoming material?" the answer should point directly to these documented requirements.
PPAP Submission Levels and Material Documentation
Not every PPAP level requires the same depth of material documentation. Here is a practical breakdown:
| PPAP Level | Material Documentation Required | Typical Use Case |
|---|---|---|
| Level 1 | Part Submission Warrant (PSW) and limited supporting data only | Low-risk commercial parts |
| Level 2 | PSW with product samples and limited supporting data | Standard production parts |
| Level 3 | PSW with product samples and complete supporting data (including MTRs, control plan, process flow, FMEA, dimensional results) | Automotive and safety-critical stamping parts |
| Level 4 | PSW with complete supporting data, as directed by the customer | Customer-specific high-risk applications |
| Level 5 | PSW with complete supporting data, available for review at the supplier's site | Highest scrutiny applications |
For most custom stamping parts we manage, Level 3 is the standard requirement from our U.S. clients. This means the supplier must submit the full MTR as part of the PPAP package. If the MTR is missing, the PPAP is automatically incomplete and will be rejected.
Using MTR Data for Design for Manufacturability
Here is something many buyers overlook: the certified material properties from the MTR are not just for compliance. They are critical inputs for Design for Manufacturability (DFM) analysis. When our engineering team reviews a new stamping part design, we use the actual yield strength and elongation values from the MTR — not the nominal textbook values — to predict forming behavior. This helps us identify potential cracking zones, springback issues, and die wear patterns before cutting steel for tooling.
If your supplier cannot provide an MTR with real mechanical property data, your DFM analysis is based on assumptions. And assumptions in stamping lead to tool rework, delayed timelines, and wasted money.
Historical MTR Data and Supplier Performance
Over time, I recommend building a database of MTR data from each supplier. This allows you to analyze batch-to-batch variation in the raw material they procure. If a supplier's material consistently shows tensile strength values near the upper limit of the specification, that tells you something about their raw material sourcing practices. It may also explain patterns in dimensional variation or tool wear on your stamping parts.
This kind of analysis feeds directly into your supplier qualification process. A supplier who consistently delivers material with tight, centered property values is a more reliable partner than one whose material properties swing across the full specification range. Industry standards like IATF 16949 encourage this type of data-driven supplier evaluation, and it strengthens your position during any quality audit.
Conclusion
Requesting material test reports and certificates is not bureaucracy — it is your primary defense against stamping part failure. Specify your requirements early, verify every heat number, and never approve a shipment without the documentation in hand.
Frequently Asked Questions
What specific material certifications should I demand to ensure my stamping parts meet my engineering specs?
One trade-off I weigh on every new stamping project is how deeply to specify material certification requirements — too vague and you get generic paperwork, too prescriptive and you scare off capable suppliers who simply use different document formats.
How can I verify that the Material Test Reports provided by my Vietnam supplier are actually authentic?
A lesson we learned early in our Vietnam operations is that not every document stamped with a factory seal tells the full truth — and the buyer who trusts without verifying is the one who pays the price.
Should I require a full MTR and heat lot traceability before I approve the final shipment of my custom parts?
A buyer interaction last year drove this point home for me. A U.S. client approved a shipment of stamped mounting brackets without reviewing the MTR. Two weeks after the parts arrived, his customer's incoming inspection flagged the hardness as out-of-spec. We traced the issue to a material substitution the Vietnamese stamping shop made without informing anyone. Full heat lot traceability would have caught this before the container left the port.
Footnotes
1. Explains what a Material Test Report is and its purpose in the metals industry. ↩︎
2. Provides an overview of the metal stamping process and its applications. ↩︎
3. Defines material traceability and its importance in the metals supply chain. ↩︎
4. Replaced HTTP 404 link with an authoritative government-related source explaining third-party conformity assessment. ↩︎
5. Defines a Mill Test Certificate and its key information in the metals industry. ↩︎
6. Explains the purpose and content of a Certificate of Analysis, especially for regulated products. ↩︎
7. Details the EN 10204 standard for inspection documents, including type 3.1. ↩︎
8. Explains what chemical composition is and its significance in metals and alloys. ↩︎
9. Replaced HTTP 403 link with a comprehensive article on understanding mechanical properties of materials, relevant to manufacturing. ↩︎
10. Provides a comprehensive overview of the Production Part Approval Process (PPAP). ↩︎
.jpg)