Skip to main content

🇻🇳 178 profiles · Engineering review

Vietnam Manufacturing

What Causes Cracking or Breakage in Stamping Parts?

July 23, 2026

Assembly line at Bueno Technology, a DEWIN-audited Vietnamese factory

Overview of common causes behind cracking or breakage in stamping parts

Cracking or breakage in stamping parts nearly derailed one of our bracket projects last year. A split flange can scrap a whole batch, delay your launch, and strain your budget. Our engineering team learned to treat it as a system problem — and solve it before production.

Cracking or breakage in stamping parts happens when local stress or strain exceeds the metal’s forming limit. Common causes include low material ductility, sharp die radii, excessive tonnage, poor lubrication, incorrect blank holder force, worn tooling, and hidden material defects like inclusions or uneven hardness.

Cracks are rarely caused by one single mistake. They usually come from a mix of material, tooling, and process issues. Let me walk you through how to find and fix each one.

How can I identify the root cause of cracking in my stamped parts?

A buyer once sent us photos of split Z-clips and asked, "Is the steel bad?" Our team traced it to a die radius instead. Location told us the whole story.

Identify the root cause by examining where the crack appears. Cracks at bends suggest radius or grain-direction issues. Cracks at drawn-cup bottoms point to draw ratio or holder force. Edge cracks indicate trimming or clearance problems. Corner cracks signal die-design stress concentration.

Diagram showing where cracks appear to identify root cause in stamped parts

Crack diagnosis works best when you treat the defect like evidence at a scene. The crack's position, shape, and timing all narrow down the cause. In our project reviews, we always start with three questions: where did it crack, when did it crack, and how does the fracture surface look?

Read the crack location first

The location is the fastest clue. A crack along a bend line behaves very differently from a tear in a deep-drawn wall. Here is the diagnostic map we use when we audit stamping suppliers in Vietnam and across Asia:

Crack Location Most Likely Cause First Thing to Check
Along a bend line Bend radius too small, grain direction Radius-to-thickness ratio, rolling direction
Bottom of drawn cup Draw ratio too large, holder force too high Draw reduction per stage, blank holder setting
Side walls of drawn part Friction, insufficient material flow Lubrication, die clearance
Cut or trimmed edges Punch-die clearance, dull tooling Clearance percentage, tool wear
Complex corners Stress concentration in die design Corner radii, forming sequence

Check the timing of the failure

Timing matters too. Cracks that appear during forming point to process or tooling issues. Cracks that appear hours or days later suggest hydrogen embrittlement 1 from plating or pickling, or residual stresses released over time. We once helped a US client whose parts cracked three days after electroplating. The stamping process was fine. The plating bath was the culprit.

Look at the fracture surface

A ductile tear looks fibrous and dull. A brittle crack looks flat and shiny. Ductile tears usually mean the process pushed the metal too far. Brittle cracks usually mean the material itself had a problem. This simple visual check saves weeks of guessing.

✔ The location of a crack is one of the most reliable clues to its root cause True
Different failure mechanisms produce cracks in predictable places — bend lines, drawn walls, or trimmed edges — so mapping the location narrows the diagnosis quickly.
✘ If a stamped part cracks, the raw material must be defective False
The same sheet often forms perfectly in one tool and fails in another, which proves that die design and process settings are frequently the dominant factors, not the material.
Video: Sample metal parts from audited Vietnamese factories in the DEWIN network. (@dewintech)

What material defects could be causing breakage in my custom stampings?

Sourcing custom parts across Vietnam and Asia has taught our team a hard lesson: mill certificates 2 do not always match the coil on the press. Material verification pays for itself.

Material defects that cause breakage include low ductility, excessive or uneven hardness, internal inclusions and voids, insufficient sheet thickness, wrong alloy grade for the geometry, and residual stresses from coil processing. Hydrogen embrittlement after plating can also cause delayed cracking.

Material defects like low ductility and voids causing breakage in custom stampings

Material problems are sneaky because the sheet can look perfect on the surface. The defects that break stampings usually hide inside the metal or inside the paperwork. Let me break down the main categories we screen for.

Ductility versus hardness

Every metal has a forming limit. Harder material generally has less ductility left to give. If your part needs deep draws or tight bends, a high-hardness sheet may already be near its limit before the press cycles once. We always match the temper and grade to the most demanding feature on the drawing, not to the flat areas.

Hidden internal defects

Inclusions, pores, and voids act like tiny pre-existing cracks. Under tensile strain, they open up and propagate. Uneven hardness across a coil is just as bad. One section forms fine, and the next section splits under identical settings. That inconsistency confuses troubleshooting badly, because operators chase a process fault that does not exist.

Thickness and grade selection

Thin sheet with inadequate tensile strength 3 will split when the draw depth or stretch demand is too high. Here is a simplified guide we use during design reviews with clients:

Material Factor Risk If Wrong Prevention Step
Ductility / elongation Splits in bends and draws Verify elongation values on the mill cert
Hardness uniformity Random, inconsistent cracks Sample hardness testing across the coil
Inclusions / voids Cracks starting mid-material Source from audited, reputable mills
Thickness Thinning and tearing in high-strain zones Match gauge to draw depth and bend radius
Residual coil stress Cracks during later forming Proper leveling before blanking

Delayed cracking after plating

Hydrogen embrittlement deserves special attention. Pickling and electroplating can push hydrogen into the steel. Parts pass final inspection, then crack in the box. If your parts are plated high-strength steel, a post-plating bake is cheap insurance.

✔ Hydrogen embrittlement can cause stamped parts to crack hours or days after production True
Pickling and electroplating can introduce hydrogen into high-strength steel, causing delayed brittle cracking long after the parts leave the press.
✘ Harder material is always better because it makes stronger stamped parts False
Higher hardness usually means lower ductility, so overly hard sheet reaches its forming limit sooner and cracks more easily during bending or drawing.

How does tooling design affect the risk of cracking in my stamping parts?

Reviewing die designs 4 before tool steel gets cut is one of our standard project steps. A single sharp corner in a drawing can doom an otherwise sound stamping program.

Tooling design affects cracking risk through die corner radii, punch-die clearance, blank holder and draw bead design, alignment, and wear condition. Sharp corners and small radii concentrate stress, wrong clearance tears edges, and worn or misaligned tooling creates uneven strain that initiates cracks.

Tooling design factors like die radii and clearance affecting cracking risk

Tooling is where most preventable cracks are born. The die decides how the metal flows, where strain concentrates, and how much of the material's ductility gets consumed. In my experience reviewing tools for bracket and clip projects, five design elements deserve the most scrutiny.

Radii and stress concentration

Metal hates sharp corners. A small die corner radius forces the sheet to stretch instead of flow, and strain piles up at that point. In deep drawing 5, too small a lower die corner radius is a classic direct cause of bottom cracks. As a rough rule, bend radii below one material thickness sharply raise the cracking risk in most steels.

Clearance between punch and die

Clearance that is too tight shears the edge with excessive stress, leaving micro-cracks that grow during later forming. Clearance that is too loose creates heavy burrs and rollover, which also act as crack starters. Edge condition matters more than most buyers realize, because a rough trimmed edge often fails during a later bend, not during the cut itself.

Blank holder force and draw beads

This is a balancing act, not a maximization problem:

  1. Too much holder force locks the blank, so the wall stretches and tears.
  2. Too little holder force lets the flange wrinkle, and wrinkles crack later.
  3. Draw beads fine-tune flow in specific zones — powerful, but easy to overdo.

Wear and alignment

Even a well-designed die degrades. Chipped punches, dull edges, and misalignment distribute force unevenly across the part. On progressive dies 6, cumulative strain across stations compounds the problem. We ask suppliers for documented tool maintenance intervals, because a die that made good parts in month one can crack parts by month six.

Complex parts with multiple bends, flanges, and draws face all these risks at once. That is why simple parts rarely crack and complex ones often do.

What quality control steps can I request to prevent breakage in my stamping orders?

Greg, a purchasing manager we work with in the US, once told me he only trusts suppliers who get it right the first time. Our QC checklist was built around exactly that expectation.

Request material certification with incoming verification, first-article inspection with a documented PPAP, in-process checks on tonnage and lubrication, tooling wear inspection schedules, trial runs before full production, and final inspection covering crack-prone zones. Add bake-out verification for plated high-strength parts.

Quality control steps to request for preventing breakage in stamping orders

Prevention beats troubleshooting every time. When we manage stamping orders for corporate clients, we structure quality control around the full lifecycle of the order, not just the final inspection. You can request the same structure from any supplier, and a good one will welcome it.

Build QC into every stage

Here is the framework we apply on custom stamping projects, from material receipt to shipment:

Stage QC Step to Request What It Prevents
Material intake Mill cert review plus hardness and thickness spot checks Wrong grade, uneven hardness, thin stock
Pre-production First-article inspection and PPAP documentation Die design faults reaching mass production
Trial run Sample forming with strain and thinning checks Marginal process windows
In-process Tonnage monitoring, lubrication checks, SPC on key dimensions Drift toward the forming limit
Tool maintenance Scheduled wear inspection with records Cracks from dull or chipped tooling
Post-plating Hydrogen bake verification for high-strength steel Delayed embrittlement cracking
Final inspection Visual and dye-penetrant checks on crack-prone zones Escapes reaching your dock

Ask for evidence, not promises

Reports matter more than reassurances. Request first-article inspection reports with actual measured values. Ask for photos of crack-prone areas — bend lines, drawn walls, trimmed edges — under good lighting. For safety-critical parts, dye-penetrant testing 7 on a sampling basis catches hairline cracks that visual inspection misses.

Insist on trial runs

A short trial run before full production is the cheapest insurance available. It reveals whether the process window is comfortable or marginal. When our Vietnam team runs trials, we deliberately check parts from the start, middle, and end of the coil, because material variation often hides between coil sections. If a supplier resists a trial run, treat that as a warning sign about their process discipline.

✔ A documented trial run before mass production is one of the most effective ways to prevent cracking escapes True
Trial runs expose marginal process windows, material variation, and tooling issues while corrections are still cheap, long before a full batch is at risk.
✘ Final inspection alone is enough to guarantee crack-free stamping orders False
Hairline cracks and delayed hydrogen embrittlement can escape visual final checks, so quality must be built in at material intake, tooling, and process stages — not inspected in at the end.

Conclusion

Cracking or breakage in stamping parts wastes money and delays launches. But it is diagnosable and preventable — control material, tooling, process, and QC together, and your parts arrive right the first time.

Frequently Asked Questions

How can I identify the root cause of cracking in my stamped parts?

A buyer once sent us photos of split Z-clips and asked, "Is the steel bad?" Our team traced it to a die radius instead. Location told us the whole story.

What material defects could be causing breakage in my custom stampings?

Sourcing custom parts across Vietnam and Asia has taught our team a hard lesson: mill certificates 2 do not always match the coil on the press. Material verification pays for itself.

How does tooling design affect the risk of cracking in my stamping parts?

Reviewing die designs 4 before tool steel gets cut is one of our standard project steps. A single sharp corner in a drawing can doom an otherwise sound stamping program.

Footnotes


1. Explains the metallurgical mechanism behind delayed cracking after plating processes. ↩︎


2. ASTM sets material certification standards referenced when verifying mill certs. ↩︎


3. Defines the material property that determines splitting risk during forming. ↩︎


4. ASME provides authoritative engineering standards for tooling and die design practices. ↩︎


5. Background on the sheet metal forming process directly linked to cup-bottom cracking. ↩︎


6. NIST manufacturing resources cover multi-station tooling processes like progressive dies. ↩︎


7. Explains the nondestructive testing method referenced for detecting hairline cracks in parts. ↩︎

Manufacturing RFQ

Have a STEP Model or 2D Drawing for This Project?

Share your drawing, material, quantity and finishing requirements to begin a manufacturing quote. Confirm pricing, delivery and inspection requirements during the review.

Upload CAD & Get Quote →

This article is part of DEWIN's technical manufacturing engineering knowledge base. Factory-specific details come from each factory's profile page — please verify current information there or with our team.

Quick Sourcing Inquiry