Skip to main content

🇻🇳 178 profiles · Engineering review

Vietnam Manufacturing

What Common Quality Defects Should You Look For When Sourcing Stamping Parts?

July 10, 2026

Production floor at Nhi Binh Plastic, a DEWIN-audited Vietnamese factory

Common quality defects to identify when sourcing custom metal stamping parts

Every week, our quality team in Vietnam reviews incoming stamping parts — and the same defects keep showing up from suppliers who skip proper process control 1.

Common quality defects in stamping parts include burrs, cracking, wrinkling, springback, dimensional inaccuracies, surface scratches, and material thinning. Identifying these defects early during sourcing prevents costly rework, assembly failures, and shipment delays for U.S. buyers importing from Asian suppliers.

This guide breaks down each defect category, explains root causes, and shares the quality control measures we use to catch problems before parts ever leave the factory floor drawing tolerances 2. If you source custom stamped components from Asia, this is your practical checklist.

How can I identify and prevent common surface defects like burrs or cracks in my custom stamping parts?

One lesson we learned early in our contract manufacturing work: a supplier can hit every dimension on the drawing and still ship parts that fail at assembly — because nobody checked the edges or surfaces closely enough ultrasonic thickness measurements 3.

Surface defects like burrs, cracks, and scratches in stamping parts are identified through visual inspection, tactile checks, and magnification tools. Prevent them by enforcing strict die maintenance schedules, proper punch-to-die clearance, adequate lubrication, and incoming material verification at your supplier's facility.

Identifying and preventing surface defects like burrs and cracks in custom stamping parts

Burrs: The Most Frequent Offender

Burrs 4 are sharp, raised edges left along the cut line of a stamped part. They happen when the cutting edge of a punch or die becomes dull, or when the clearance between punch and die is wrong. I have seen cases where a 0.05 mm shift in clearance turned a clean edge into a hazardous one. Burrs affect how parts seat in assemblies. They create safety risks for workers handling the parts. And they often mean the tooling needs immediate attention.

When we audit stamping suppliers, we always check burr height against the drawing specification. Many U.S. buyers specify burr direction too — meaning which side of the part the burr is allowed on. If the supplier does not understand this, parts fail incoming inspection at the buyer's facility.

Cracking and Splitting

Cracks typically appear at bend lines, near holes, or in deep-drawn areas. The root cause is often a mismatch between the material properties and the forming operation. If the material is too hard, or if the die radius is too tight, the metal simply cannot stretch far enough. It fractures.

We flag cracking risk during the PPAP phase 5. Our engineers review the drawing, the selected material grade, and the proposed die design together. If the forming depth is aggressive, we push the supplier to run trial samples first and inspect them under magnification.

Surface Scratches, Galling, and Staining

Scratches come from rough die surfaces, contaminated material, or careless handling between stations. Galling — a type of adhesive wear 6 — happens when metal transfers from the part to the die surface due to poor lubrication. Staining is typically corrosion or chemical contamination.

Here is a quick reference for the most common surface defects:

Surface Defect Visual Indicator Primary Root Cause Prevention Method
Burrs Sharp raised edges along cut lines Dull tooling or incorrect clearance Regular die sharpening, clearance checks
Cracks Visible fracture lines at bends or draws Material too hard, tight die radii Material testing, die radius optimization
Scratches Linear marks on flat surfaces Dirty dies, rough handling Clean dies, protective handling protocols
Galling Rough, smeared surface patches Inadequate lubrication Proper lubrication systems, die polishing
Staining Discolored areas on surface Corrosion, chemical contamination Clean storage, protective coatings

The key takeaway: surface defects are not just cosmetic. Burrs interfere with fit. Cracks cause field failures. Scratches on plated parts lead to corrosion. Each one must be addressed at the source.

✔ Burrs are most commonly caused by worn tooling or incorrect punch-to-die clearance True
As cutting edges degrade, they no longer shear the material cleanly, leaving excess material along the edge. Incorrect clearance has the same effect by creating uneven shearing forces.
✘ Minor burrs are always acceptable and do not affect part performance False
Even small burrs can prevent parts from seating properly in assemblies, cause injury during handling, and create interference in precision fits. Acceptability depends entirely on the application and drawing specification.
Video: Sample metal parts from audited Vietnamese factories in the DEWIN network. (@dewintech)

What dimensional inaccuracies should I watch for to ensure my stamped components meet my strict drawing tolerances?

A buyer we work with in the Midwest once rejected an entire shipment of brackets because the hole-to-edge distance was off by 0.3 mm. The supplier had never measured that dimension. It was on the drawing, but it was not on their inspection checklist.

Watch for out-of-tolerance hole positions, inconsistent bend angles from springback, feature misalignment, overall profile deviations, and flatness errors. Use go/no-go gauges, CMM checks, and first-article inspection reports to verify every critical dimension before production ramps up.

Verifying dimensional accuracy and tolerances for stamped components using CMM and gauges

Springback and Bend Angle Deviation

Springback 7 is the elastic recovery of sheet metal after forming. The metal bends to the desired angle, then partially springs back toward its original flat state. The result is an under-bent part. High-strength materials like stainless steel or advanced high-strength steels exhibit more springback than mild steel.

Compensating for springback requires over-bending in the die design. But this only works if the material properties are consistent batch to batch. If the supplier switches material lots without re-validating, the bend angles can shift.

Hole Position and Feature Alignment

When a stamping die has multiple stations, each station must be precisely aligned. If locating pins wear down or the strip feed is inconsistent, features drift out of position. This is especially critical for parts with multiple holes that mate with fasteners in an assembly.

We require our suppliers to measure hole positions on first articles using coordinate measuring machines 8. For ongoing production, in-process inspection with calibrated pin gauges catches drift before it becomes a batch problem.

Flatness and Profile Accuracy

Flat parts that come out with a bow or twist will not sit flush in an assembly. This kind of deformation is often caused by uneven stress distribution during blanking or by residual stresses in the raw material. Parts with large flat areas and thin material are most at risk.

Here is a breakdown of common dimensional defects and their detection methods:

Dimensional Defect Typical Tolerance Impact Detection Method Root Cause
Springback Bend angle off by 1°–5° Angle gauge, CMM Material elasticity, insufficient overbend
Hole position drift ±0.1 mm to ±0.5 mm shift Pin gauge, CMM Worn locating pins, strip feed error
Feature misalignment Holes or slots not concentric Optical comparator Die station misalignment
Profile deviation Overall shape out of spec Contour gauge, CMM Die wear, press tonnage variation
Flatness error Bow or twist across surface Surface plate, feeler gauge Residual stress, uneven blanking force

Why Dimensional Accuracy Starts at the Die Design Stage

The best time to prevent dimensional problems is before the first part is stamped. Die design must account for the specific material grade, thickness, and forming sequence. Our approach during co-development is to review the die layout with the supplier and confirm that critical dimensions are measurable at each station. We also push for process capability studies (Cpk) on key dimensions during the pilot run. This gives us data, not just samples.

Statistical process control is not optional for tight-tolerance stamping. When we set up a new program, we define which dimensions go on the SPC chart. The supplier tracks them in real time. If a dimension trends toward the tolerance limit, they adjust before parts go out of spec. Understanding how supplier tooling and fixture capabilities impact sheet metal precision is essential to getting this right from the start.

✔ Springback compensation must be designed into the die before production begins True
Once a die is hardened and in production, modifying it for springback compensation is expensive and time-consuming. Proper simulation and over-bend allowances must be built in during the die design phase.
✘ If a first-article sample passes inspection, all subsequent parts will be within tolerance False
Tool wear, material variation between coils, and press parameter drift all cause dimensions to shift over a production run. Continuous in-process inspection and SPC are essential to maintain dimensional accuracy.

How do I verify that the material thickness and structural integrity of my parts haven't been compromised during the stamping process?

The trade-off between forming complexity and material integrity is one we discuss with suppliers at the start of every deep drawing project. Push the metal too far, and walls thin out. Pull back too much, and you need more forming stages, which increases cost.

Verify material thickness and structural integrity by requiring incoming material certifications, performing ultrasonic thickness measurements on formed parts, conducting hardness testing at critical zones, and inspecting for thinning, tearing, or necking — especially in deep-drawn areas and tight-radius bends.

Checking material thickness and structural integrity of metal parts during the stamping process

Wall Thinning in Deep Drawing

Deep drawing stretches sheet metal into a three-dimensional shape. As the material flows over the punch radius and into the die cavity, the walls thin. Some thinning is normal and expected. But excessive thinning weakens the part. If the tensile strength of the material is exceeded locally, necking occurs — a visible narrowing that precedes tearing.

We specify maximum allowable thinning percentages on critical parts. For example, if the nominal material thickness is 1.0 mm, we may allow a maximum thinning of 20%, meaning the wall cannot go below 0.8 mm at any point. The supplier measures this with an ultrasonic thickness gauge at designated points after forming.

Material Certification and Incoming Inspection

Every coil of steel or aluminum that enters a stamping facility should come with a mill test certificate 9. This document lists the chemical composition, mechanical properties (yield strength, tensile strength, elongation), and actual thickness. If the supplier does not verify incoming material against the certificate, there is no way to know if the material matches the drawing specification. Learning how to evaluate supplier raw material sourcing reliability is a critical step in preventing these material-related defects.

Our Vietnam and China offices conduct supplier audits that include reviewing incoming material inspection records. We check whether the supplier actually tests incoming coils or just files the certificates without verification.

Grain Structure and Anisotropy

Sheet metal is not uniform in all directions. The rolling process creates a grain structure that makes the material stronger in one direction than another. This anisotropy affects how the metal forms. If a part is oriented incorrectly relative to the grain direction, it may crack or wrinkle where it otherwise would not.

For critical stamping parts, we ask the supplier to document the rolling direction on the blank layout. This small step prevents a category of defects that is otherwise very difficult to diagnose after the fact.

Integrity Check What It Detects Tool / Method When to Perform
Ultrasonic thickness measurement Wall thinning, necking UT thickness gauge After forming, at critical zones
Hardness testing Work hardening, material change Rockwell or Vickers tester After forming, at bend areas
Visual / magnified inspection Tearing, micro-cracks 10x–30x magnification After each forming stage
Mill certificate verification Wrong material grade or thickness Document review, caliper check At incoming material receipt
Grain direction check Anisotropy-related defects Blank layout review, etch test Before blanking

Advanced Detection for Hidden Defects

Micro-cracks and sub-surface flaws are invisible to the naked eye. They are dangerous because they reduce the fatigue life of a part. In safety-critical applications — think automotive brackets or structural mounting clips — these hidden defects can lead to field failures.

Eddy current testing 10 and dye penetrant inspection are two non-destructive methods that catch what visual inspection misses. We recommend these for any stamped part that will bear a load or experience cyclic stress. The cost of these tests is minimal compared to the cost of a product recall.

What quality control measures should my Asian supplier use to eliminate part deformation before shipping to my U.S. facility?

When we first started managing stamping programs out of Vietnam, one of the most common complaints from our U.S. clients was parts arriving deformed. Not cracked, not out of tolerance on paper — just bent, twisted, or warped. The root causes ranged from bad packing to poor process control to no final inspection at all.

Your Asian supplier should implement first-article inspection per PPAP standards, SPC on critical dimensions, in-process checks at every forming stage, final inspection with go/no-go gauges, proper deburring, and secure packaging with anti-deformation supports to eliminate part deformation before shipping.

Quality control measures to prevent part deformation during manufacturing and international shipping

First-Article Inspection and PPAP

The Production Part Approval Process is the foundation. Before mass production begins, the supplier produces a small batch of parts using production tooling and production conditions. These parts are measured against every dimension on the drawing. The results go into a first-article inspection report. If anything is out of spec, the supplier corrects it before ramping up.

We manage the PPAP process for our clients. Our engineers review the measurement data, check gauge repeatability, and confirm that the supplier's control plan covers every critical characteristic. This front-end investment saves enormous time and cost downstream.

In-Process Inspection and SPC

A stamping press runs fast. Progressive dies can produce hundreds of parts per hour. Without in-process inspection, a die shift or material variation can produce thousands of defective parts before anyone notices.

We require suppliers to pull samples at defined intervals — typically every 200 to 500 parts, depending on the complexity. Operators measure critical dimensions and log the data. For high-volume runs, SPC charts track trends. If a measurement approaches the control limit, the operator stops the press and adjusts. You can learn more about how to develop supplier performance KPIs for quality to formalize these expectations with your supplier.

Final Inspection and AQL Sampling

Before any shipment leaves the factory, a final inspection should be performed. We follow AQL (Acceptable Quality Level) sampling plans, typically AQL 1.0 for critical defects and AQL 2.5 for major defects. Our inspectors check dimensions, surface quality, burr condition, and overall appearance.

Here is a typical quality control workflow we set up for stamping suppliers:

Step 1: Incoming material inspection — verify mill certificates, measure thickness, check surface condition.
Step 2: First-article inspection — full dimensional layout per PPAP.
Step 3: In-process inspection — sample checks at defined intervals, SPC on key dimensions.
Step 4: Post-forming inspection — check for deformation, thinning, cracks.
Step 5: Final inspection — AQL sampling, visual and dimensional checks.
Step 6: Packaging inspection — verify anti-deformation supports, proper labeling.

Packaging: The Last Line of Defense

I cannot overstate how often good parts get damaged by bad packaging. Thin stamped brackets stacked loosely in a box will deform under their own weight during a transpacific shipment. Parts with sharp features scratch each other. Humidity causes corrosion on uncoated steel.

We specify packaging requirements as part of the control plan. For delicate parts, this means individual compartments, foam inserts, or VCI (Vapor Corrosion Inhibitor) bags. For heavier parts, it means palletizing with proper weight distribution and strap-down protocols.

The Role of Digital Tools

An emerging trend in stamping quality control is the use of digital twin technology and AI-driven predictive analytics. These systems model the stamping process digitally and predict where defects are likely to occur. While not yet standard at most Asian suppliers, we are seeing early adoption among tier-one facilities. For U.S. buyers sourcing mid-to-high complexity parts, asking about a supplier's digital quality capabilities is worth the conversation.

✔ Proper packaging is a critical quality control step that prevents deformation during international shipping True
Stamped parts, especially thin-walled brackets and clips, are vulnerable to bending and warping from vibration, stacking pressure, and handling during weeks of ocean freight. Packaging design must account for these forces.
✘ A final inspection alone is sufficient to guarantee defect-free stamping parts False
Final inspection is a sampling-based check. It catches defects statistically but cannot inspect every part. Without in-process controls and SPC, systemic defects can pass through final inspection undetected.

Conclusion

Sourcing stamping parts from Asia demands vigilance across surface defects, dimensional accuracy, material integrity, and process control. Build quality into the process — from die design through packaging — and you prevent problems instead of reacting to them.

Frequently Asked Questions

How can I identify and prevent common surface defects like burrs or cracks in my custom stamping parts?

One lesson we learned early in our contract manufacturing work: a supplier can hit every dimension on the drawing and still ship parts that fail at assembly — because nobody checked the edges or surfaces closely enough ultrasonic thickness measurements 3 .

What dimensional inaccuracies should I watch for to ensure my stamped components meet my strict drawing tolerances?

A buyer we work with in the Midwest once rejected an entire shipment of brackets because the hole-to-edge distance was off by 0.3 mm. The supplier had never measured that dimension. It was on the drawing, but it was not on their inspection checklist.

How do I verify that the material thickness and structural integrity of my parts haven't been compromised during the stamping process?

The trade-off between forming complexity and material integrity is one we discuss with suppliers at the start of every deep drawing project. Push the metal too far, and walls thin out. Pull back too much, and you need more forming stages, which increases cost.

Footnotes


1. Explains systematic monitoring and adjustment of manufacturing processes. ↩︎


2. Explains allowable deviations from specified dimensions on engineering drawings. ↩︎


3. Describes non-destructive method for measuring material thickness using sound pulses. ↩︎


4. Details causes, treatment, and prevention of burrs in metal stamping. ↩︎


5. Explains the Production Part Approval Process for ensuring consistent part quality. ↩︎


6. Found an authoritative Wikipedia page on wear, which includes a section on adhesive wear. ↩︎


7. Describes elastic recovery of sheet metal after forming, affecting final shape. ↩︎


8. Found an authoritative Wikipedia page explaining coordinate measuring machines (CMMs). ↩︎


9. Found an authoritative Wikipedia page explaining mill test reports (certificates). ↩︎


10. Found an authoritative Wikipedia page explaining eddy current testing. ↩︎

Manufacturing RFQ

Have a STEP Model or 2D Drawing for This Project?

Share your drawing, material, quantity and finishing requirements to begin a manufacturing quote. Confirm pricing, delivery and inspection requirements during the review.

Upload CAD & Get Quote →

This article is part of DEWIN's technical manufacturing engineering knowledge base. Factory-specific details come from each factory's profile page — please verify current information there or with our team.

Quick Sourcing Inquiry