Skip to main content

🇻🇳 178 profiles · Engineering review

Vietnam Manufacturing

What Are the Common Stamping Parts Used in Architectural Hardware?

July 23, 2026

High-tonnage mechanical and hydraulic stamping press at AN THANH TECHNOLOGY COMPANY LIMITED, a DEWIN-audited manufacturing facility

Common stamped metal parts used in architectural hardware manufacturing

Sourcing stamping parts for architectural hardware sounds simple until a shipment of out-of-tolerance brackets stalls a whole building project PPAP documentation 1. I have watched that happen to buyers more than once.

Common stamping parts in architectural hardware include hinges, brackets, mounting plates, connector plates, clips, strike plates, latch components, washers, grilles, and drawer-slide parts. They are typically stamped from steel, stainless steel, aluminum, or brass for doors, windows, cabinetry, HVAC, and structural support.

That answer covers the part families. But choosing the right process, material, and supplier is where projects succeed or fail PPAP documentation 2. Let me walk you through each step.

How Do I Choose the Right Stamping Process for Architectural Hardware Parts?

A buyer once sent our team a hinge drawing quoted three ways by three suppliers, each proposing a different process. The confusion was understandable, because process choice depends on geometry, volume, and tolerance.

Choose progressive die stamping for high-volume parts like hinges and clips, deep drawing for cup-shaped or enclosed forms, and single-stage blanking or bending for simple, low-volume brackets. Match the process to part complexity, annual quantity, tolerance requirements, and your tooling budget.

Progressive die stamping and deep drawing processes for architectural hardware parts

Process selection is the first real decision in any stamping project. Get it wrong, and you either overpay for tooling or accept parts that never hold tolerance.

The Main Stamping Processes at a Glance

Process Best For Typical Volume Tooling Cost
Progressive die Hinges, clips, multi-feature brackets 50,000+ per year High
Deep drawing 3 Cups, housings, recessed plates Medium to high Medium–high
Compound blanking Flat plates, washers, strike plates Medium Medium
Single-stage bending Simple angle brackets, low volumes Low to medium Low
Fineblanking 4 Lock components needing smooth edges High Very high

How I Break the Decision Down

First, look at annual volume. Progressive dies cost more upfront, but they amortize quickly at high quantities. In our experience managing tooling projects in Vietnam, a progressive die pays for itself fast on a hinge program running six figures per year. On a run of five thousand brackets, it never does.

Second, look at geometry. A part with multiple bends, punched slots, and formed tabs — like the zigzag mounting clips we handle regularly — suits a progressive die where each station adds one feature. A deep, seamless recess needs drawing instead.

Third, look at tolerance and edge quality. Standard blanking leaves a slight burr and shear zone. Lock faceplates and latch parts that need clean, functional edges may justify fineblanking or a secondary deburring step.

Finally, consider springback. High-strength steels bounce back after bending. A good toolmaker compensates in the die design. We always ask suppliers how they plan to handle springback before we approve tooling drawings, because fixing it after the die is cut costs time and money.

✔ Progressive die stamping 5 becomes more cost-effective as annual volumes rise True
The high tooling cost is spread across many parts, so per-unit cost drops sharply at volumes of roughly 50,000 pieces or more per year.
✘ One stamping process can efficiently produce any architectural hardware part False
Each process has geometric and volume limits; deep recesses need drawing, clean sheared edges need fineblanking, and simple brackets are often cheapest with single-stage tooling.
Video: Sample metal parts from audited Vietnamese factories in the DEWIN network. (@dewintech)

What Materials Should I Specify for Durable Architectural Hardware Stampings?

There is a trade-off I weigh on almost every hardware RFQ: corrosion resistance versus cost. Stainless steel solves rust problems, but not every bracket hidden inside a cabinet needs it.

Specify cold-rolled or galvanized steel for hidden structural stampings, stainless steel (304 or 316) for exposed or humid environments, aluminum for lightweight parts, and brass for decorative or antimicrobial surfaces. Match material grade to exposure, load, finish requirements, and budget.

Stainless steel, aluminum, and brass materials for durable architectural hardware stampings

Material choice drives roughly half the unit cost of a stamped hardware part. It also determines how the part performs over a building's lifetime. So it deserves more thought than it usually gets on drawings.

Matching Material to Application

Material Strengths Weaknesses Typical Parts
Cold-rolled steel Strong, cheap, formable Rusts without coating Hidden brackets, connector plates
Galvanized steel Built-in corrosion barrier Zinc can flake at sharp bends Joist hangers, framing clips
Stainless 304 Good corrosion resistance Higher cost, springback Hinges, strike plates, grilles
Stainless 316 Coastal and chemical resistance Highest cost Marine-adjacent hardware
Aluminum 5052 Light, corrosion resistant Lower strength Window hardware, trim clips
Brass Decorative, antimicrobial Soft, expensive Handles, faceplates, escutcheons

Visible Versus Hidden Hardware

I encourage buyers to split their bill of materials into two groups. Visible hardware — hinges, handles, lock plates, grilles — must look good and stay that way. Here, stainless steel or brass with a proper finish earns its price. Hidden hardware — joist hangers, reinforcement clips, mounting plates — must carry load and resist corrosion inside walls. Galvanized or coated steel usually wins on value.

Do Not Forget the Finish

The base metal is only half the story. Zinc plating, powder coating, and anodizing all extend part life and change appearance. When we review drawings for our U.S. clients, missing finish specs are one of the most common gaps we flag. A drawing that says "steel bracket" without a plating callout invites a supplier to ship bare metal. Then the parts arrive with surface rust after an ocean crossing. Always specify the coating type, thickness, and any salt-spray requirement 6 in writing.

✔ Steel is the most widely used material for architectural hardware stampings True
Steel offers the best balance of strength, formability, and cost, and with zinc plating or galvanizing it handles most indoor structural applications well.
✘ Stainless steel is always the safest default choice for stamped hardware False
Stainless costs significantly more and exhibits greater springback in forming; for hidden, dry-environment parts, coated carbon steel performs just as well at lower cost.

How Can I Ensure Consistent Quality When Sourcing Stamped Hardware Components from Asia?

Early in my career at our Singapore office, a client showed me a box of stamped clips where every fifth part had a torn tab. The supplier had never inspected first articles. That lesson shaped how our QC team in Vietnam works today.

Ensure consistent quality by approving first-article samples against the drawing, requiring PPAP documentation, auditing the supplier's press shop, defining inspection criteria for burrs and springback, and running independent final inspections before shipment. Written specifications and staged checkpoints prevent most defects.

Quality inspection steps for sourcing stamped hardware components from Asia

Distance is the real enemy in overseas sourcing. You cannot walk onto the press floor, so your quality system has to do the walking for you. Here is the checkpoint sequence we apply on stamping projects for our American clients.

A Five-Stage Quality Gate Process

  1. Supplier audit before award. Check press tonnage, die maintenance records, and measurement equipment. A shop without a die maintenance schedule will drift out of tolerance mid-production.
  2. Drawing review and agreement. Confirm every tolerance, material grade, and finish spec is understood. Many defects trace back to overlooked drawing notes, not bad workmanship. Our engineers translate critical callouts and confirm them line by line with the factory.
  3. First-article inspection and PPAP. Measure sample parts fully before mass production starts. Getting it right the first time is far cheaper than rework or air-freighting replacements.
  4. In-process control. Require hourly checks on critical dimensions during production runs. Stamping dies wear, and burr height grows as punches dull.
  5. Final inspection before loading. An independent check on dimensions, finish, packaging, and quantity. This is the last chance to catch problems before the container sails.

Know the Common Stamping Defects

Watch for springback on bends, cracking at tight radii, wrinkling on drawn parts, distortion on thin flat plates, and burrs on sheared edges. Put acceptable limits for each defect in your quality agreement. If the standard is not written down, you cannot enforce it later. On our projects, we also retain golden samples signed by both sides, so any dispute has a physical reference point.

✔ Stamping dies wear during production and cause dimensional drift over time True
Punch and die edges dull with every stroke, which increases burr height and shifts dimensions, so in-process checks and die maintenance schedules are essential.
✘ Approving a good first-article sample guarantees the full production run will conform False
First articles only prove the tooling can make a good part; without in-process controls and final inspection, tool wear and setup errors can still produce defective batches.

Which Custom Stamping Capabilities Should I Look for in an Architectural Hardware Supplier?

A purchasing manager once asked me why two quotes for the same connector plate differed by forty percent. The answer sat in capabilities: one supplier had in-house tooling and plating, the other subcontracted both.

Look for in-house tool design and maintenance, progressive and deep-draw press capacity, secondary operations like tapping and welding, integrated surface finishing, engineering support for DFM feedback, documented process control, and export experience with your market's standards such as ANSI/BHMA or CE.

Custom stamping capabilities to evaluate in an architectural hardware supplier

Capability gaps show up as delays, subcontracting risk, and inconsistent quality. So evaluating a stamping supplier means looking well beyond the press room. Here is the checklist we use when we audit stamping factories in Vietnam and across Asia for our clients.

The Capability Checklist

Capability Why It Matters Red Flag If Missing
In-house tooling Fast die repairs, controlled lead times Weeks lost waiting on outside toolmakers
Press range (25–400T+) Handles thin clips to thick plates Parts subcontracted without your knowledge
Secondary operations Tapping, riveting, spot welding in-house Extra logistics, added defect points
Surface finishing Plating and powder coating control Inconsistent finish, rust claims
DFM engineering support Catches design problems before tooling Costly die revisions after kickoff
Measurement equipment CMM, optical comparators, gauges Inspection by eye and tape measure
Export documentation PPAP, material certs, compliance records Customs and certification headaches

Engineering Support Separates Good From Average

The best stamping suppliers push back on drawings. They flag a bend radius that is too tight for the material, or a hole placed too close to an edge. That feedback, given before tooling starts, saves weeks. When we co-develop hardware parts with clients, we deliberately route drawings through this DFM loop before any steel is cut for the die.

Certifications and Standards Matter More Than Ever

Architectural hardware sold in North America often needs ANSI/BHMA 7 compliance, and fire-rated hardware carries stricter material and tolerance rules. European projects need CE-aligned documentation. Ask your supplier to show prior experience with your target standard, not just a general quality certificate on the wall. A supplier who has shipped compliant strike plates to the U.S. before will already understand the tolerance discipline your project requires.

Conclusion

Stamped hinges, brackets, plates, clips, and latch parts quietly hold buildings together. Choose the right process, specify materials precisely, enforce staged quality gates, and audit supplier capabilities before you commit.

Frequently Asked Questions

How Do I Choose the Right Stamping Process for Architectural Hardware Parts?

A buyer once sent our team a hinge drawing quoted three ways by three suppliers, each proposing a different process. The confusion was understandable, because process choice depends on geometry, volume, and tolerance.

What Materials Should I Specify for Durable Architectural Hardware Stampings?

There is a trade-off I weigh on almost every hardware RFQ: corrosion resistance versus cost. Stainless steel solves rust problems, but not every bracket hidden inside a cabinet needs it.

How Can I Ensure Consistent Quality When Sourcing Stamped Hardware Components from Asia?

Early in my career at our Singapore office, a client showed me a box of stamped clips where every fifth part had a torn tab. The supplier had never inspected first articles. That lesson shaped how our QC team in Vietnam works today.

Footnotes


1. PPAP is an established quality standard; linking to ISO clarifies its formal basis for buyers. ↩︎


2. Defines PPAP, a quality documentation requirement described in the sourcing process. ↩︎


3. Background on deep drawing process used for cup-shaped hardware forms. ↩︎


4. Provides technical detail on fineblanking mentioned in the process comparison table. ↩︎


5. Explains the progressive die process referenced for high-volume hardware parts. ↩︎


6. ISO corrosion testing standard relevant to specifying finish and salt-spray requirements. ↩︎


7. Official standards body reference for ANSI/BHMA compliance mentioned for hardware suppliers. ↩︎

Manufacturing RFQ

Have a STEP Model or 2D Drawing for This Project?

Share your drawing, material, quantity and finishing requirements to begin a manufacturing quote. Confirm pricing, delivery and inspection requirements during the review.

Upload CAD & Get Quote →

This article is part of DEWIN's technical manufacturing engineering knowledge base. Factory-specific details come from each factory's profile page — please verify current information there or with our team.

Quick Sourcing Inquiry