Sourcing stamping parts for aerospace programs taught our team one hard lesson: a single missed standard can ground an entire shipment at customs or, worse, halt a production line.
Standards that apply to stamping parts for aerospace industry purchases include AS9100 certification for quality management, AMS material specifications for aerospace grade alloys, AS9102 First Article Inspection for dimensional verification, NADCAP accreditation for special processes, FAA PMA/TSO for airworthiness, and MIL-STD-130 or AS478-3 for part marking and material traceability.
Each of these standards addresses a different layer of risk — from raw material integrity 1 to final part identification. Below, we break down the four most critical questions procurement managers ask when qualifying stamping suppliers for aerospace work.
How do I verify aerospace stamping suppliers meet AS9100 requirements?
A few years back, one of our U.S. clients awarded a stamping contract to a supplier who claimed AS9100 compliance — only to discover during a pre-shipment audit that the supplier held an expired certificate and had no counterfeit parts prevention program in place, delaying the project by three months.
To verify aerospace stamping suppliers meet AS9100 requirements, confirm their current AS9100D certificate through the OASIS (Online Aerospace Supplier Information System) database, audit their risk management and configuration management procedures, and validate that counterfeit parts prevention controls are documented and active.
/12-05-2025-Pictures%20-%20Name/Hydraulic%20press%201.jpg)
Why AS9100D Is Non-Negotiable
AS9100D is not just an upgraded ISO 9001. It is the aerospace-specific quality management system that Boeing, Airbus, Lockheed Martin, and other major OEMs require from every direct supplier. Without it, a stamping facility simply cannot appear on an approved supplier list for any Tier 1 or Tier 2 aerospace program.
The standard layers critical aerospace additions on top of ISO 9001:2015. These include configuration management 2, operational risk management, and — increasingly important — a formal counterfeit parts prevention program. When we conduct supplier audits in Vietnam and across Asia, we look specifically at how the facility documents these controls. A certificate on the wall is not enough.
Key AS9100D Elements to Audit
| AS9100D Requirement | What to Check | Red Flag If Missing |
|---|---|---|
| Counterfeit Parts Prevention | Written procedure, incoming inspection for material authenticity | Supplier cannot verify raw stock origin |
| Configuration Management | Change control records for tooling and process revisions | No revision history on stamping dies |
| Risk Management | PFMEA or equivalent risk assessment for each part family | Risk analysis done only at quote stage |
| Product Safety | Documented process for identifying safety-critical characteristics | No special marking or control for critical dimensions |
| Customer-Specific Requirements | Evidence of flowing down OEM specs to sub-tier suppliers | Only generic AS9100 procedures, no OEM-specific work instructions |
The OASIS Database Check
The quickest way to verify a supplier’s AS9100 certification is through the OASIS database maintained by the International Aerospace Quality Group (IAQG). This database lists every accredited certificate, its scope, its expiration date, and any nonconformances. We recommend buyers run this check before the first phone call with a potential supplier.
OEM-Specific Layers
Be aware that AS9100D is only the baseline. Boeing imposes additional requirements through D6-82479. Airbus uses AIMS. These OEM-specific standards often demand stricter sampling plans, digital data packages instead of paper reports, and unique testing methods. A supplier who is AS9100-certified but unfamiliar with these layered requirements will likely fail an OEM audit. When our team manages PPAP for aerospace clients, we always map the OEM flowdown requirements before production starts.
What material certifications should I require for aerospace stamped parts?
The trade-off between cost and compliance hits hardest at the material stage. We have seen buyers save a few cents per kilogram on sheet metal only to face a full lot rejection because the mill cert did not meet AMS material specifications.
For aerospace stamped parts, require AMS (Aerospace Material Specifications) certifications for every raw material lot, mill test reports confirming chemical composition and mechanical properties per ASTM E8/E8M, full heat and lot traceability from melt source to finished part, and DFARS compliance documentation when the end use is U.S. defense.

Understanding AMS vs. ASTM
AMS specifications are published by SAE International. They define the exact chemical composition, mechanical properties, and processing conditions for aerospace grade alloys. ASTM standards, such as ASTM E8/E8M for tensile testing 4, are used to verify those properties in the lab. Both work together. AMS tells you what the material must be. ASTM tells you how to test it.
What a Complete Material Data Package Looks Like
| Document | Purpose | Who Issues It |
|---|---|---|
| Mill Test Report (MTR) | Confirms chemical composition and mechanical properties of the raw stock | Steel mill or metal producer |
| AMS Certification | Verifies material meets the specific aerospace material specification called out on the drawing | Mill or authorized distributor |
| Certificate of Conformance (CoC) | Supplier's declaration that material meets all purchase order requirements | Stamping supplier |
| DFARS Compliance Letter | Confirms material is sourced from a qualifying country per Defense Federal Acquisition Regulation Supplement | Supplier or distributor |
| Heat/Lot Traceability Record | Links the finished stamped part back to the original melt source | Stamping supplier (maintained through production) |
Material Traceability: The Chain Must Not Break
Material traceability is the backbone of aerospace quality. Every stamped bracket, clip, or mounting component must trace back to its original heat number. If a metallurgical defect is discovered later, the OEM needs to know exactly which parts are affected. In our supply chain work, we require suppliers to stamp or engrave heat numbers on raw stock and carry those numbers through every production step — blanking, forming, trimming, and finishing.
When the part is destined for a U.S. defense program, DFARS compliance adds another layer. The raw material must originate from a qualifying country. This is not optional. Failure to document DFARS compliance can result in contract termination and legal exposure. For more on what to request from your suppliers, see our guide on material certifications for US sheet metal fabrication compliance.
Special Process Material Testing
Some aerospace stamping applications require non-destructive testing 5 (NDT) of the raw material before forming. Eddy current testing, ultrasonic inspection, or dye penetrant checks may be specified on the engineering drawing 6. These special processes often require NADCAP accreditation from the testing lab. We always verify that the material supplier or an independent lab holds the correct NADCAP scope before approving any incoming material lot.
Which quality inspection standards ensure my aerospace parts pass PPAP approval?
One interaction sticks with me. A purchasing manager in Ohio told us his previous supplier delivered 5,000 stamped brackets that looked perfect — until the First Article Inspection report came back with 14 out-of-tolerance dimensions. The entire lot was scrapped. That is a preventable failure.
To ensure aerospace stamped parts pass PPAP approval, require AS9102 First Article Inspection with 100% balloon drawing verification, implement process capability studies (Cpk ≥ 1.67 for critical features), use statistical sampling per the OEM's specific requirements, and deliver digital inspection data packages with full measurement records.

AS9102 First Article Inspection: Every Feature, Every Time
AS9102 is the aerospace standard for First Article Inspection (FAI). It requires the supplier to measure every single dimension, note, and characteristic on the engineering drawing — not just the critical ones. The first production part gets a complete balloon drawing markup. Every balloon number links to a measured value, a tolerance, and a pass/fail result.
This is different from automotive PPAP, where some features may be sampled. In aerospace, the FAI is exhaustive. Our team reviews every FAI report before it goes to the client. We check for completeness, proper balloon numbering, and correct reference to the drawing revision. For practical guidance on structuring this process, see our article on how to request a First Article Inspection (FAI) report when sourcing sheet metal fabrication.
The Three Forms of AS9102
AS9102 uses three standardized forms:
| Form | Name | Content |
|---|---|---|
| Form 1 | Part Number Accountability | Part number, revision, material, drawing number, supplier info |
| Form 2 | Product Accountability — Raw Material | Material specification, heat/lot number, supplier, test results |
| Form 3 | Characteristic Accountability | Every dimension measured, nominal value, tolerance, actual value, pass/fail |
All three forms must be completed. Missing any form is grounds for PPAP rejection.
Process Capability and In-Process Controls
Beyond the FAI, ongoing production requires statistical process control. Most aerospace OEMs expect a Cpk of at least 1.67 for critical characteristics — tighter than the 1.33 common in automotive. This means the stamping process must be highly stable and centered.
Real-time press tonnage monitoring is becoming standard practice. By tracking the force applied on every stroke, the supplier creates a digital fingerprint for each stamped part. If the tonnage drifts outside the control window, the press stops automatically. This kind of Industry 4.0 integration is something we actively look for when auditing stamping facilities.
Digital Data Packages
Boeing and Airbus now require digital transmission of inspection data. Paper reports are no longer acceptable for many programs. The shift to Model-Based Definition 7 (MBD) under ASME Y14.41 means that 3D CAD data — not 2D blueprints — increasingly serves as the primary technical authority. Suppliers must be capable of inspecting against 3D models and exporting results in digital formats.
Our experience managing PPAP submissions has shown that suppliers who invest in CMM (Coordinate Measuring Machine) equipment with automated reporting software pass approval cycles significantly faster than those relying on manual measurement and hand-written reports.
How do I choose a stamping partner compliant with NADCAP and FAA regulations?
The lesson we learned managing supply chains across Asia is this: compliance is not a checkbox. It is a culture. A supplier can hold NADCAP accreditation for heat treating and still fail an FAA audit if their documentation practices are sloppy or their ITAR compliance program is informal.
To choose a NADCAP and FAA-compliant stamping partner, verify current NADCAP accreditation for all special processes (heat treating, NDT, chemical processing), confirm FAA PMA or TSO authorization if supplying aftermarket parts, ensure ITAR compliance for defense components, and audit the supplier's part marking practices against MIL-STD-130 or AS478-3.

NADCAP Accreditation: What It Covers
NADCAP is the National Aerospace and Defense Contractors Accreditation Program. It accredits specific special processes — not the entire facility. A supplier may hold NADCAP for heat treating but not for non-destructive testing. You must match the accreditation scope to the processes your part requires.
Common NADCAP scopes relevant to stamping include:
- Heat treating (stress relief, age hardening after forming)
- Chemical processing (plating, anodizing, passivation)
- Non-destructive testing (dye penetrant, magnetic particle, eddy current)
- Welding (if the stamped part is later welded into an assembly)
FAA PMA and TSO: When They Apply
FAA Parts Manufacturer Approval 8 (PMA) is required for aftermarket or replacement parts. If your stamped component will be sold as a spare part for an aircraft already in service, PMA is mandatory. It involves proving that the part meets the original Type Certificate holder's design data and passes conformity inspection.
FAA Technical Standard Order (TSO) authorization applies to parts that must meet specific minimum performance standards. Not all stamped parts need TSO, but it is critical for components in certain systems.
For parts destined for European-registered aircraft, EASA Part 21 Subpart G is the equivalent production organization approval. A part approved under FAA PMA does not automatically satisfy EASA requirements. Dual compliance is necessary for global supply chains.
ITAR and Export Control
For any stamped part that goes into a military aircraft or defense system, ITAR compliance is mandatory. The International Traffic in Arms Regulations 9 control the export of defense articles and technical data. Your stamping supplier must be ITAR-registered, and all technical drawings and specifications must be handled under ITAR protocols.
Our offices in both Vietnam and Singapore manage ITAR-sensitive projects by maintaining strict data access controls and ensuring that only authorized personnel handle controlled technical data. This is a non-negotiable requirement for any U.S. defense procurement.
Part Marking: Commercial vs. Defense
| Requirement | Commercial Standard | Defense Standard |
|---|---|---|
| Marking Standard | AS478-3 | MIL-STD-130 |
| Required Content | Fabricator trademark, part number, OEM part number | UID (Unique Identification), 1D/2D machine-readable codes |
| Method | Ink stamping, engraving, or labels | Direct Part Marking (laser etching) preferred |
| Traceability | Lot-level | Unit-level (each individual part) |
| Regulatory Body | FAA (14 CFR Part 45) | DoD |
The industry trend is moving toward Direct Part Marking using laser technology. Machine-readable 2D Data Matrix codes are embedded permanently onto the part surface. This supports automated traceability across the entire lifecycle — from production through maintenance, repair, and overhaul.
Cybersecurity as a New Gate
A newer requirement catching many suppliers off guard is the Cybersecurity Maturity Model Certification (CMMC). For defense programs, stamping facilities must now demonstrate cybersecurity controls to protect sensitive digital designs and supply chain data. This is becoming a procurement prerequisite, not just a recommendation.
Additionally, the AS13100 standard is gaining traction for aero-engine supply chains. It harmonizes supplemental quality requirements across engine manufacturers and their sub-tier suppliers. If your stamped parts feed into engine programs, expect AS13100 to appear in purchase order flowdowns.
Conclusion
Purchasing stamping parts for aerospace demands layered compliance — from AS9100 certification and AMS material specifications to AS9102 inspection, NADCAP accreditation, and proper part marking. Verify every layer before production starts, and partner with a supply chain team that understands these standards from the inside.
Frequently Asked Questions
How do I verify aerospace stamping suppliers meet AS9100 requirements?
A few years back, one of our U.S. clients awarded a stamping contract to a supplier who claimed AS9100 compliance — only to discover during a pre-shipment audit that the supplier held an expired certificate and had no counterfeit parts prevention program in place, delaying the project by three months.
What material certifications should I require for aerospace stamped parts?
The trade-off between cost and compliance hits hardest at the material stage. We have seen buyers save a few cents per kilogram on sheet metal only to face a full lot rejection because the mill cert did not meet AMS material specifications.
Which quality inspection standards ensure my aerospace parts pass PPAP approval?
One interaction sticks with me. A purchasing manager in Ohio told us his previous supplier delivered 5,000 stamped brackets that looked perfect — until the First Article Inspection report came back with 14 out-of-tolerance dimensions. The entire lot was scrapped. That is a preventable failure.
Footnotes
1. Overview of material selection and integrity factors in engineering and manufacturing. ↩︎
2. Overview of configuration management processes used to maintain product consistency and traceability. ↩︎
3. Official organization responsible for the AS9100 series and the OASIS database. ↩︎
4. Official ASTM standard for tension testing of metallic materials. ↩︎
5. PRI’s official page for NADCAP accreditation in non-destructive testing processes. ↩︎
6. Overview of engineering drawings used to communicate technical requirements in manufacturing. ↩︎
7. Official ASME standard for digital product definition and 3D CAD data practices. ↩︎
8. FAA’s official guidance on Parts Manufacturer Approval for aerospace components. ↩︎
9. Official U.S. Department of State landing page for the International Traffic in Arms Regulations (ITAR). ↩︎
