A few months ago, one of our U.S. clients rejected an entire shipment of stamped brackets because the bend heights varied by 0.3 mm — a dimension that fell well within standard formed-feature tolerances but outside the unrealistic ±0.1 mm they had specified on every single dimension. The rework cost them three weeks and thousands of dollars Geometric Dimensioning and Tolerancing 1. The root cause was not poor quality. It was a tolerance grade mismatch between what the drawing demanded and what stamping physics can actually deliver. This is a problem we see repeatedly when helping buyers source custom parts from Asian suppliers, and it is entirely preventable.
When purchasing stamping parts, you should know ISO 2768 (classes f, m, c, v), DIN 6930-2 (grades f, m, g, sg), and the ST1–ST11 / FT1–FT10 precision scales. Most general stamped parts only need ISO 2768 Medium (±0.1–0.3 mm), while precision pierced features can hold ±0.05 mm. Specifying tighter grades than necessary drives up cost exponentially.
The sections below break down each standard, explain what tolerances are realistic for different features, and give you a practical framework for communicating requirements to overseas manufacturers without overpaying or under-specifying.
What tolerance grades should I specify when sourcing stamping parts from Asian suppliers?
Last year, our engineering team in Vietnam reviewed over 60 sets of customer drawings for stamped parts projects. More than half referenced no tolerance standard at all — just a general note saying "tight tolerances required." That vagueness forces suppliers to guess, and guessing leads to either over-engineered pricing or under-spec parts.
When sourcing stamping parts from Asian suppliers, specify ISO 2768 Medium (m) for general linear dimensions, DIN 6930-2 for stamped steel, and ST/FT grades for precision requirements. Always note the tolerance class on your drawing title block so every supplier quotes against the same baseline.

Understanding the Three-Tier Tolerance Hierarchy
Think of tolerance standards as a layered system. At the top sits the governing standard — ISO 2768 or DIN 6930-2 — which sets the rules. Below that sits the tolerance class or grade, which sets the precision level within those rules. And at the bottom sits the feature-specific tolerance, which defines what is achievable for a particular hole, bend, or contour.
ISO 2768 is the global baseline. It is the most widely recognized general tolerance standard 2 for sheet metal and machined parts. It defines four classes:
| ISO 2768 Class | Label | Typical Linear Tolerance (for dims <30 mm) | Common Use Case |
|---|---|---|---|
| Fine | f | ±0.05 mm | Precision assemblies, electronics |
| Medium | m | ±0.1 mm | General structural parts, automotive brackets |
| Coarse | c | ±0.3 mm | Non-critical structural components |
| Very Coarse | v | ±0.5 mm | Rough fabrications, guards |
Most automotive structural parts default to Medium (m) or Coarse (c). Unless your part has a critical fit requirement, Medium is the right starting point.
DIN 6930-2 is a German standard designed specifically for stamped steel parts 3, both flat and hot stampings. It uses a similar class structure (f, m, g, sg) but its tolerance values are calibrated to what stamping processes can achieve "in normal workshop accuracy." If your supplier is European or serves European OEMs, they will likely reference this standard.
Decoding ST and FT Grades
Many Asian suppliers, especially those in China, use a parallel precision scale:
| Grade Type | Range | Highest Precision | Lowest Precision | Applies To |
|---|---|---|---|---|
| ST (Flat Parts) | ST1 – ST11 | ST1 | ST11 | Blanked, pierced flat features |
| FT (Formed Parts) | FT1 – FT10 | FT1 | FT10 | Bent, drawn, formed features |
ST1 represents precision stamping — the kind of dimensional accuracy you need for tight-fitting electrical connectors or medical devices. ST11 is for rough structural components where a few tenths of a millimeter do not matter. When I review quotes from our partner factories, I always confirm which ST or FT grade they are pricing against. If they quote ST3 but your part only needs ST7, you are overpaying.
What to Put on Your Drawing
Here is what I recommend to every buyer we work with:
- Add "General tolerances per ISO 2768-m" to your title block.
- Call out tighter tolerances only on critical features — hole positions, mating surfaces, datum references.
- If you need DIN 6930-2, state the specific grade (e.g., "DIN 6930-2 grade m").
- For Asian suppliers using ST/FT scales, ask them to confirm which grade they can hold and map it to your ISO class.
This approach eliminates ambiguity. Every supplier reads the same baseline, and you only pay extra for the features that truly need it.
How do I know if my supplier can actually hold the tolerances stated on my drawings?
During a recent supplier audit at a stamping facility in Vietnam, I asked the plant manager to show me their SPC data for a bracket with ±0.1 mm hole-to-hole tolerance. He pulled up the charts immediately — Cpk values above 1.33 for every critical dimension. That told me more than any sales brochure ever could.
To verify a supplier's tolerance capability, request SPC data, Cpk reports, and a PPAP submission before production. Ask for sample measurements on first articles. A capable supplier will show Cpk ≥ 1.33 for critical dimensions and will openly share their process control methodology with you.
/ICHI-%20Photo/150-ton%20Stamping%20Press%20Machine%201.jpg)
The Capability Question Most Buyers Skip
Many purchasing managers accept a supplier's claim at face value: "Yes, we can hold ±0.05 mm." But can they hold it consistently across 50,000 parts? Across three shifts? After the die has run 500,000 cycles? Tooling precision degrades over time. Die wear causes dimensional drift. A supplier who can hit a tight tolerance on a first article may struggle to maintain it at volume.
Here is the framework I use when evaluating suppliers for our clients:
Step 1: Request First Article Inspection Reports (FAIR). These should include measurements of every dimensioned feature, taken with calibrated equipment. We require CMM (coordinate measuring machine 4) data for parts with Geometric Dimensioning and Tolerancing callouts.
Step 2: Ask for SPC and Cpk data. Statistical Process Control charts show whether the process is stable. A Cpk of 1.33 means the process can hold the tolerance with a comfortable margin. Below 1.0 means the process is not capable — parts will drift out of spec.
Step 3: Review die maintenance records. Progressive dies wear down. Burr height increases as punches dull. Flatness and parallelism degrade as die surfaces wear. A well-managed factory schedules preventive die maintenance at defined intervals — every 100,000 hits, for example — and records the results.
What to Look for in Measurement Reports
| Verification Item | What to Ask For | Red Flag |
|---|---|---|
| Dimensional accuracy | CMM report with all GD&T callouts | Missing dimensions, hand-written reports |
| Process stability | SPC charts with Cpk values | Cpk below 1.0 for critical features |
| Die condition | Maintenance log with hit counts | No scheduled maintenance plan |
| Material verification | Mill certificates for sheet metal 5 thickness | No traceability to coil source |
| Surface quality | Burr height measurements | No burr spec or measurement method defined |
The PPAP Approach
For our U.S. clients, we run a full PPAP (Production Part Approval Process 6) on every new stamped part. This includes dimensional results, material certs, process flow diagrams, control plans 7, and measurement system analysis. It is extra work upfront, but it catches problems before they become shipments of non-conforming parts.
One specific thing I always check: whether the supplier measures parts in a "restrained" or "free-state" condition. For thin-gauge stampings, a part can flex under its own weight. If the supplier measures it flat on a surface plate (restrained) but your inspection measures it hanging freely, you will get different numbers — and false rejections. Specify the measurement condition on your drawing.
Material springback is another factor that affects measurement. A bend target of 90° may measure 88° or 92° depending on sheet metal thickness, material grade, and grain direction. The supplier must compensate for this in the die design and verify the result in-process.
Which tolerance standards should I reference to avoid costly miscommunication with overseas manufacturers?
One of our clients once sent a drawing to three different Asian suppliers. The drawing had no general tolerance note. One supplier quoted to ISO 2768 Fine. Another assumed DIN 6930-2 Medium. The third applied their own internal standard. The quotes varied by 40%, and none of them were wrong — they just interpreted the silence differently.
To avoid costly miscommunication, always reference ISO 2768 (with the specific class: f, m, c, or v) on your drawing title block. For stamped steel parts, add DIN 6930-2 if your supply chain is European. For precision features requiring fits, reference ISO 286 with the appropriate IT grade (IT6, IT7, or IT8).
/12-05-2025-Pictures%20-%20Name/Hydraulic%20press%201.jpg)
ISO 2768 vs. DIN 6930-2 vs. ISO 286: When to Use Each
These three standards serve different purposes. Confusing them — or omitting them — is the single biggest source of tolerance-related disputes I see in cross-border sourcing.
ISO 2768 covers general tolerances for linear dimensions, angular dimensions, and geometric tolerances (flatness, perpendicularity, symmetry). It is your default. If you only reference one standard, make it this one. For a deeper dive into standard precision and tolerance ranges for sheet metal fabrication, we have a detailed breakdown available.
DIN 6930-2 is narrower. It applies specifically to stamped steel parts and accounts for the unique process characteristics of blanking, piercing, and forming. European automotive OEMs often require it. If your end customer is a German automaker, reference this standard alongside ISO 2768.
ISO 286 is for fits — shaft-and-hole relationships. Use it when a stamped hole must accept a pin, dowel, or press-fit component 8 with a controlled interference or clearance. The IT grades define the tolerance band width:
| ISO 286 IT Grade | Tolerance Band (for 10–18 mm nominal) | Application |
|---|---|---|
| IT6 | 0.011 mm | Precision fits, ground surfaces |
| IT7 | 0.018 mm | General engineering fits |
| IT8 | 0.027 mm | Less critical fits |
| IT9 | 0.043 mm | Free-running clearance |
Most stamped holes do not need IT6. A reamed or secondary-machined hole might. A simple clearance hole for an M6 bolt needs nothing tighter than IT12 or IT13. Specifying IT6 on a bolt clearance hole is a classic over-tolerancing mistake.
Feature-Specific Tolerance Capabilities
Not every feature on a stamped part can be held to the same precision. Here is a realistic breakdown:
Pierced features (holes, slots): These are cut in a flat blank before forming. Same-plane piercing is extremely repeatable — ±0.05 mm (±0.002 inches) between holes is standard. This is where precision stamping excels.
Formed features (bends, draws): Material springback makes these inherently less precise. Allow ±1° for angular tolerances on bends. For formed heights, ±0.38 mm (±0.015 inches) is realistic. Trying to hold ±0.1 mm on a bend height without secondary operations will cause rejection issues.
Edge-to-edge dimensions: Standard capability is ±0.13 mm (±0.005 inches) on blanked edges. This tightens if the die is new and loosens as wear progresses.
The Grain Direction Factor
The orientation of a part relative to the metal's grain direction significantly impacts bending and forming accuracy. Bends made across the grain are more predictable. Bends along the grain are more prone to cracking and dimensional variation. If your part has critical bends, call out the grain direction on the drawing — or at minimum, discuss it with your supplier during DFM review.
How can I balance tighter tolerances with cost and lead time when ordering custom stamped parts?
A buyer we work with recently needed a mounting bracket with 12 dimensioned features. Initially, every feature was toleranced at ±0.05 mm. After a DFM session 9 with our partner factory, we identified that only two of those features — the mounting holes that interface with a mating assembly — actually needed that precision. The rest could comfortably live at ISO 2768 Medium. The result: a 35% reduction in piece price and two weeks shorter lead time.
To balance tighter tolerances with cost and lead time, apply the "critical few" principle: hold tight tolerances only on functional features (mating holes, datum surfaces) and use ISO 2768 Medium for everything else. This avoids secondary operations, reduces scrap, keeps tooling simpler, and opens your supplier base wider.

Why Tighter Tolerances Cost More
The relationship between tolerance and cost is not linear. It is exponential. Going from ±0.2 mm to ±0.1 mm might add 10–15% to the part cost. Going from ±0.1 mm to ±0.05 mm can add 50% or more, because it may require:
- Slower press speeds to reduce vibration
- Higher-grade tool steel (carbide inserts instead of D2)
- More frequent die sharpening to control burr height
- Secondary operations like CNC machining or reaming
- Tighter incoming material inspection for sheet metal thickness consistency
Each of these factors compounds. And tight tolerances may also limit your sourcing options. Not every stamping house has the equipment or process discipline to hold ±0.05 mm on formed features. By relaxing non-critical tolerances, you open the door to more competitive suppliers.
The Material Factor
Different materials behave differently under the punch. Here is what I have observed across projects:
| Material | Typical Piercing Tolerance | Springback Tendency | Notes |
|---|---|---|---|
| Mild Steel (SPCC, CR) | ±0.05 mm | Moderate | Most predictable; standard gauge thicknesses readily available |
| Stainless Steel (SUS304) | ±0.06 mm | High | Harder material dulls tooling faster; slightly looser piercing tolerance |
| Aluminum (5052, 6061) | ±0.05 mm | Low to moderate | Soft material; watch for burr and edge deformation |
| Copper / Brass | ±0.05 mm | Low | Excellent formability; good for precision electrical parts |
Stainless steel is the trickiest. Its work-hardening behavior means that tooling precision degrades faster, and springback is harder to predict. If your part is stainless and you need tight bend tolerances, budget for more die tryout iterations.
The DFM Conversation
Design for Manufacturing is not optional when cost matters. Here is the process I walk through with every client:
- Identify functional datums. Tie your critical tolerances to formed surfaces that the part actually references in assembly — not to raw blanked edges.
- Use bilateral tolerances (±) for centered features like holes and slots. Use unilateral tolerances (+0/−X) for edge clearances where you need to prevent interference.
- Keep hole-to-edge distances above 1.5× material thickness. Tighter spacing distorts the material and makes tolerances impossible to hold.
- Stick to standard gauge thicknesses. Non-standard gauges with tight tolerances are a double penalty — you pay for specialty material and you pay for tighter process control.
- Discuss restrained vs. free-state measurement upfront for any part thinner than 1.0 mm. This prevents false rejections.
Modern servo-presses help. They use real-time feedback loops 10 to adjust stamping force and speed, compensating for coil-to-coil material hardness variability. Suppliers running servo-presses can generally hold tighter tolerances more consistently than those running conventional mechanical presses. When evaluating suppliers, ask what press technology they use.
Digital twin simulations are also becoming more common. Some of our partner factories now run forming simulations before cutting steel for the die. These simulations predict tolerance stack-up, springback compensation requirements, and potential material flow issues. It reduces the number of physical tryout iterations and shortens time to production-ready parts.
The Purchasing Checklist
Before you send your next stamping RFQ, run through this list:
- Did you specify "General tolerances per ISO 2768-m" (or another appropriate class) in the title block?
- Did you call out tighter tolerances only on functional, mating features?
- Did you avoid specifying ±0.05 mm or tighter on formed features like bends and drawn heights?
- Did you define your measurement datums on formed (assembled) surfaces, not raw blanked edges?
- Did you specify restrained or free-state measurement for thin-gauge parts?
- Did you note material grade and standard gauge thickness?
- Did you discuss grain direction requirements for critical bends?
If you can answer yes to all of these, you are ahead of 90% of the RFQs we receive. And you will get better pricing, faster delivery, and fewer quality disputes. For more guidance on effectively communicating OEM tolerance requirements to sheet metal fabrication suppliers, we have a dedicated guide that covers the communication process in detail.
Conclusion
Getting tolerance grades right when purchasing stamping parts is not about demanding the tightest numbers. It is about matching the right standard — ISO 2768, DIN 6930-2, or ST/FT grades — to each feature's actual function, so you pay only for the precision you truly need. If you are sourcing parts for the automotive sector, understanding the quality requirements for automotive stamping parts will further help you align tolerance specifications with industry expectations.
Frequently Asked Questions
What tolerance grades should I specify when sourcing stamping parts from Asian suppliers?
Last year, our engineering team in Vietnam reviewed over 60 sets of customer drawings for stamped parts projects. More than half referenced no tolerance standard at all — just a general note saying "tight tolerances required." That vagueness forces suppliers to guess, and guessing leads to either over-engineered pricing or under-spec parts.
How do I know if my supplier can actually hold the tolerances stated on my drawings?
During a recent supplier audit at a stamping facility in Vietnam, I asked the plant manager to show me their SPC data for a bracket with ±0.1 mm hole-to-hole tolerance. He pulled up the charts immediately — Cpk values above 1.33 for every critical dimension. That told me more than any sales brochure ever could.
Which tolerance standards should I reference to avoid costly miscommunication with overseas manufacturers?
One of our clients once sent a drawing to three different Asian suppliers. The drawing had no general tolerance note. One supplier quoted to ISO 2768 Fine. Another assumed DIN 6930-2 Medium. The third applied their own internal standard. The quotes varied by 40%, and none of them were wrong — they just interpreted the silence differently.
Footnotes
1. Official ASME page for the Y14.5 standard, the global authority on GD&T principles. ↩︎
2. Official ISO page for the primary general tolerance standard used in manufacturing and engineering. ↩︎
3. Comprehensive Wikipedia overview of the metal stamping process and manufactured steel components. ↩︎
4. Authoritative Wikipedia entry for CMM technology used in industrial metrology and quality control. ↩︎
5. Authoritative Wikipedia definition and overview of sheet metal materials and industrial forms. ↩︎
6. Authoritative Wikipedia explanation of the PPAP quality standard used in manufacturing. ↩︎
7. Authoritative source for the APQP framework which mandates the use of control plans. ↩︎
8. ISO standard for limits and fits, essential for designing mating press-fit components. ↩︎
9. Authoritative Wikipedia overview of Design for Manufacturability (DFM) principles and practices. ↩︎
10. Authoritative Wikipedia entry explaining the technical mechanism of closed-loop feedback control systems. ↩︎